Notifications
Clear all
12/02/2024 5:19 am
Free NACE NACE-CIP1-001 Dumps are shared online. You can view and discuss NACE NACE-CIP1-001 questions and answers for free below. FreeCoating Inspector Level 1 Exam Questions.
12/02/2024 5:19 am
You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining.
Your FIRST preferred course of action is to:
- A . Break the blisters to see what's inside
- B . Document the problem and advise the Contractor and Owner's representative
- C . Document the problem and advise the Contractor
- D . Extract any liquid that may be inside the blister and send it to the lab for further analysis
Suggested Answer: B
12/02/2024 5:19 am
Dew point is the temperature at which
- A . water freezes.
- B . humidity decreases
- C . condensation occurs.
- D . the air is saturated.
Suggested Answer: C
12/02/2024 5:19 am
If a contractor is using a poorly maintained compressor to supply air for abrasive blast cleaning and conventional airspray, the coating inspector should perform a
- A . dry film thickness (DEI) measurement.
- B . wet film thickness (WFT) measurement.
- C . blotter test for the presence of oil and water.
- D . vial lest.
Suggested Answer: C
12/02/2024 5:19 am
Upon arrival of coating materials, the inspector should
- A . review coating contractors' plans for storage of coating materials and confirm they meet national, local and owners' fire and environmental regulations.
- B . observe and document the amount of material and batch numbers.
- C . observe aryl document that the applicator WFT at regular intervals during application.
- D . observe and document time frame and environmental conditions between each coat.
Suggested Answer: B
12/02/2024 5:19 am
Relative humidity is
- A . a measure of the amount of moisture in the air compared to saturation level.
- B . a measure of the amount of moisture in the air compared to the air temperature.
- C . the lowest temperature at which moisture forms on a steel surface.
- D . the highest temperature at which moisture forms on a steel surface.
Suggested Answer: A
12/02/2024 5:19 am
Galvanic corrosion occurs on which of the following substrates:
- A . Concrete
- B . Fiberglass Reinforced Plastic
- C . Metal
- D . Wood
Suggested Answer: C
12/02/2024 5:19 am
When applying Thermal Spray Coatings the specification is most likely to refence:
- A . SSPC PA 2
- B . NACE SP 0178
- C . NACE SP 0188
- D . SSPC-CS 23.00/AWS C2.23/NACE No. 12
Suggested Answer: D
12/02/2024 5:19 am
What is the minimum recommended distance away from an edge that an inspector should take a measurement with a dial-type magnetic pull-off Dry Film Thickness (DFT) gauge?
- A . 1 cm (.39 inch)
- B . 2.5 cm (1 inch)
- C . 6.35 cm (2.5 inch)
- D . 2.5 millimeters (.10 inch)
Suggested Answer: B
12/02/2024 5:19 am
Polymerization is the process of:
- A . Monomers telegraphing
- B . Monomers joining together
- C . All thermoplastic coatings
- D . All organic coatings
Suggested Answer: B
12/02/2024 5:19 am
An exposed area of the substrate or previous coat of a conductive coating material, often caused by poor application technique is called
- A . cracking.
- B . sagging.
- C . holiday.
- D . checking.
Suggested Answer: C
12/02/2024 5:19 am
Checking is
- A . an exposed area of the substrate or previous coat material, caused by poor application technique.
- B . a fine crack in the surface of a coating that rarely reaches the substrate
- C . a very small hole in a coating caused when air or solvent is trapped in porous film and then escapes.
- D . surface breaks in the film that often result from grease or oil contamination and revel the substrate.
Suggested Answer: B
12/02/2024 5:19 am
Inspection documentation is important because:
- A . It is the only deliverable item provided by the inspector
- B . Owners use the documentation for a variety of purposes
- C . a) only
- D . a) & b)
Suggested Answer: B
12/02/2024 5:19 am
An inspectors personal log book should contain:
- A . Subjective comments re ding the application team
- B . Objective comments regarding the application work
- C . No comments regarding the application team
- D . The inspector's personal opinions of the application team
Suggested Answer: C
12/02/2024 5:19 am
You have just received your NACE CIP Level 1 certification when you are asked to supervise a team of uncertified field pipeline inspectors.
Your FIRST preferred course of action is to:
- A . Accept the assignment without hesitation
- B . Advise the prospective employer that you cannot accept the position
- C . Meet with the prospective employer to determine the scope of your role
- D . Review the NACE Attestation prior to making a decision
Suggested Answer: C
Page 1 / 5
Next